The latest ecodesign requirement of EU Directive 2023/826 stipulates that the standby consumption of electronic devices - e.g. entertainment devices - may only be 0.5 watts. In order to achieve this target, the power losses in each semiconductor component must be carefully checked, starting with the input bridge, which is connected to the mains and is always in operation.
Diotec Semiconductor meets this requirement with its latest series of "Low Vf" or "-LV" rectifier bridges, such as the GBI25J-LV. Compared to the standard GBI25J version, this component offers a reduction in forward voltage Vf of 12% per single diode. The Vf parameter is proportional to the power dissipation as a first approximation, and since there are always two diodes per bridge, the total saving is 24% compared to the standard version. This is impressive and could be the decisive step towards achieving the eco-design requirement of only 0.5 W standby power.
查看更多
Littelfuse now is offering AEC-Q200 Rev E Qualified Fuses which developed for demanding automotive grade applications, a full complement of thin film surface mountable, cartridge, and ceramic axial-leaded fuses available for automotive and EV applications
查看更多
Diotec Semiconductor now offers a comprehensive range of various MOSFET types, from traditional THT cases via standard SMD packages to the most recent "leadless" QFN and TOLL outlines. Parts are either available in standard commercial/industrial grading or fully AEC-Q101 qualified, marked by suffix -AQ. They are offered as N, P or dual N+P channel type, and in single, dual and also H bridge configuration. Current ratings start from few Milliamps and end up at 280 Amp, while voltage ranges from 20 to 650 Volts.
查看更多
Littelfuse released new series of efuse IC provides power path protection functions such as current limiting, over voltage protection, inrush current protection and over temperature protection with real-time diagnostics. It's offering wide operation voltage ranged from 3V~24V with programmable setting and extremely small footprint.
查看更多
Diotec latest demoboard 3991 comes into play. It is equipped with the TVS diode LDP02-28AYD2-AQ, offering defined load dump protection, a peak pulse power of 6 600 W and an ESD immunity of +/- 30 kV per air and contact discharge (HBM). It comes in the industry standard TO-263AB/D²PAK outline, which allows an optimized cost/performance ratio. The demoboard further contains a fully workable USB charger circuit; therefore, it can be used to test all kinds of surge pulses and their effect on the circuit, but also for any kind of USB load.
查看更多
Littelfuse, Inc. acquired C&K on July 19, 2022. C&K is one of the most recognizable and trusted names in the electromechanical switch industry. Adding C&K’s outstanding engineering expertise and high-performance products will allow us to offer a broader product portfolio, expanded footprint, and enhanced distribution channels.
A leading designer and manufacturer of high-performance switches and interconnect solutions, C&K has a strong global presence across a broad range of end markets, including industrial, transportation, aerospace, and datacom.
查看更多
Littelfuse now offering ITV4030 series of Three-Terminal Surface Mount Battery with ampere range of 12A/15A/22A
It is a three-terminal surface mountable li-ion battery protector designed to guard against the damage caused by both overcurrent and overcharging. A fuse element is embedded to cut off the circuit when overcurrent issue happens. A heater is also directly embedded under the fuse element, it will generate heat to blow the fuse once overvoltage detected by IC or FET.
查看更多
Littelfuse announced the new SP33R6, a series of four-channel, low capacitance (0.2pF) TVS diode arrays. These robust diodes provide extremely low breakdown/turn-on voltages, making them ideal protectors of high-speed data lines with low voltage (-0.3 to +0.3V). Without performance degradation, they can safely absorb repetitive ESD strikes above the maximum level specified in IEC 61000-4-2 international standard (Level 4, ±8kV contact discharge).
The SPxxR6 TVS Diode Arrays are ideal for use in a wide range of data communications interfaces for consumer electronics, including:
USB 3.2 and 4.0,
Thunderbolt 3.0 and 4.0,
PCI Express 6.0.
The chipsets from USB 4.0 suppliers are known to be particularly susceptible to damage from voltages over 3.3V and the SP33R6 and SP00R6 TVS diode array series provides an exceptional solution for the protection of high-speed interfaces like USB 4.0 against repeated ESD strikes.
Using a multiline package footprint (SP33R6) or 0201-package (SP00R6) likely already on the circuit board, design engineers can expect ten times lower pass-through voltage when compared with existing solutions currently on the market.
查看更多
This new type of transponder was developed specially for applications where it is not possible to use one of our proven NeoTAG® transponder in Inlay, Plug or Flag versions due to the design requirement of the object. There are versions available for use with metallic and non-metallic objects. Depending on the required installation of the adhesive film transponders, different compositions can be realized with ferrite layers as the bottom or top layer. On non-metallic objects, there is no need for the ferrite film, thus creating very flat transponders. The outer dimensions can be adjusted variable to meet the application space requirements.
Due to its flexible design, this label transponder can be applied to both curved and bent surfaces.
查看更多
